How to Repair a Cracked Driveway

We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

It has been at least 10 years since I last repaved my asphalt driveway. It is in pretty good condition for the most part. I have resealed it every fall, which has been largely effective. There are a few cracks here and there, but they can be sealed using some driveway patch from Home Depot.

In the winter here in the Northeast, due to snow, ice, rain, and salting, the roadways take a beating. My driveway is no exception. I have some low spots near the road and it needs to be repaired.

So I decided to do some repairs to my cracked driveway. This article will show you how I did it and how you can too.

Materials Needed

  • 8 bags of paver base support (mixture of stone and sand)
  • 1 bag of cold driveway patch
  • 2–6 feet of plastic support strips
  • 1 bag of plastic nails
  • 2–4 gallons of extra duty driveway seal (apply two coats)
  • Paving bricks
  • Pressure-treated wood, 4 x 4 section
  • Thin plywood

Tools Needed

  • Shovel
  • Hand shovel
  • Hammer
  • Heavy duty ax
  • Wheelbarrow
  • Hacksaw
  • Tape measure
  • Flat metal plate

Total Cost of Repairing My Driveway

For an area approximately 20 feet wide by 3 feet deep, the total cost of materials was about $300.

The labor took about one week, adding up to around 20 hours in total.

Photos of My Repairs

How to Repair a Cracked Driveway

  1. Work on one section at a time. I decided to do a 3-foot section, starting at one edge and using the paving bricks as an end guide.
  2. Install a 2-foot section of the plastic guide using the nails to anchor to the ground. This acts to hold the bricks in place.
  3. Remove the cracked floor one piece at a time using the axe to chisel out the pieces.
  4. Dig up the underlying stone and sand up to 3 inches deep.
  5. Apply about 1 inch of the base support. Pour the cold asphalt over the area and keep it even.
  6. Pound the new surface using a flat metal plate.
  7. Install the 4 x 4 pressure treated wood to create a section. This is temporary support while pounding down the fill.
  8. Place a sheet of plywood over the flattened surface. Drive a car over the plywood to apply pressure. Wait a day for the mixture to settle.
  9. Add more patch on top as needed. Remove the 4 x 4 wood, and add an edge support using the plastic anchor.
  10. Repeat the process for the next section of 3 foot by 3 foot area. It is important to maintain the level of the patch such that it conforms to the surrounding area. You want to avoid a high spot or a low spot, which will attract water.
  11. When the whole strip is done, apply two coats of the driveway sealer. Wait a few days and check for cracks and fill as needed.

Note: Perform this while repair on a sunny hot day to help the settling and to seal the underground pockets of air.

Additional Repairs...

For some cracks, it is better to seal using a rope. This requires the use of a blow torch. You can buy the rope seal at Home Depot. This will prevent water from seeping into the ground and causing additional damage. Here are some photos...

Example of a Crack

Rope Repair Pli Stix

Blow Torch

© 2019 Jack Lee

Watch the video: DIY. Repairing Cracks on Your Walkway or Driveway..


  1. Dahr

    Holiday greetings! I wish health to the administrator and all visitors. There will be health, there will be everything else!

  2. Mezit

    Magnificent phrase and it is duly

  3. Nibei

    Why will all the laurels go to the author, and we will also hate him?

  4. Ivon

    I don't understand something

  5. Milabar

    You are not right. I offer to discuss it. Write to me in PM.

Write a message

Previous Article

Best time to plant fruit trees in michigan

Next Article

Bobcat landscaping